===== Ashley Vos Undergraduate Research (Aerospace Engineering) ===== Interest in the surface measurement instrument. Interested in probe flow modeling and ground electric field mills. ==== December 1st, 5:42 pm. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Pressure Transducer - find one to buy (cheap, highest accuracy) - Young, Campbell - Must connect to A/D board - Research SPI and IC2 interface - Sodder new charging port on iMet-XQ2 - Find type (read manual) and order - Look into how to label small wires - Rain Gauges (Tipping Buckets) - Wire Rain and fog gauges - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) - Wire Aerosol to Power Control Device - will need to find manual. - Connect to Wi-Fi - Record how to set up DAQ HATS - Create append method for ADPAA (Note: /home/raspberry/ADPAA/src/python_lib) == Reports == * TIMMS - DNW * iMet-XQ2 - Soldered new charging ports onto both devices at the bench. Need to test - Inquire with Dr. Delene * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work. Confirmed with Dr. Delene, will work without it and see if it becomes necessary. * Rain Gauges - Wired another AC Plug * Tipping Bucket Programming - DNW * Aerosol Particle Sizer - DNW * Wi-Fi - Connected. * DAQ HATS - Done. * Append - DNW. New Task ==== November 24, 4:38 pm. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Pressure Transducer - find one to buy (cheap, highest accuracy) - Young, Campbell - Must connect to A/D board - Research SPI and IC2 interface - Sodder new charging port on iMet-XQ2 - Find type (read manual) and order - Look into how to label small wires - Rain Gauges (Tipping Buckets) - Wire Rain and fog gauges - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) - Wire Aerosol to Power Control Device - will need to find manual. - Connect to Wi-Fi - Record how to set up DAQ HATS == Reports == * TIMMS - Finished setting up Vaisala Temperature and Humidity sensor; recorded first data! * Recorded how to set up ADPA and how to set up the Vaisala Temperature and Humidity Probe * iMet-XQ2 - The ones we have work, but we'd have to flip the orientation. Could do it. * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work. * Rain Gauges - DNW * Tipping Bucket Programming - DNW * Aerosol Particle Sizer - Coded in data acquisition parameters save for the last one. * Wi-Fi - Will work, just need username from Dr. Delene ==== November 20, 4:46 pm. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Pressure Transducer - find one to buy (cheap, highest accuracy) - Young, Campbell - Must connect to A/D board - Research SPI and IC2 interface - Sodder new charging port on iMet-XQ2 - Find type (read manual) and order - Look into how to label small wires - Rain Gauges (Tipping Buckets) - Wire Rain and fog gauges - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) - Wire Aerosol to Power Control Device == Reports == * TIMMS - DNW * iMet-XQ2 - The ones we have work, but we'd have to flip the orientation. Could do it. * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work. * Rain Gauges - DNW * Tipping Bucket Programming - * Aerosol Particle Sizer - Began wiring ==== November 19, 5:32 pm. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Pressure Transducer - find one to buy (cheap, highest accuracy) - Young, Campbell - Must connect to A/D board - Research SPI and IC2 interface - Sodder new charging port on iMet-XQ2 - Find type (read manual) and order - Look into how to label small wires - Rain Gauges (Tipping Buckets) - Set up second Raspberry Pi - Wire Rain and fog gauges - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) - Wire Aerosol to Power Control Device == Reports == * TIMMS - connected wires for temperature and humidity sensors, examined ADPAA and installed * iMet-XQ2 - DNW * Wires- DNW * Rain Gauges - Finished Cleaning * Tipping Bucket Programming - DNW * Aerosol Particle Sizer - DNW ==== November 13, evening. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Sodder new charging port on iMet-XQ2 - Find type (read manual) and order - Look into how to label small wires - Rain Gauges (Tipping Buckets) - Set up second Raspberry Pi - Wire Rain and fog gauges - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) - Resolve AnyDesk Conflict on TIMMS-SN00400 - Wire Aerosol to Power Control Device == Reports == * TIMMS - DNW * iMet-XQ2 - DNW * Wires- DNW * Rain Gauges - Cleaned * Tipping Bucket Programming - DNW * Resolved AnyDesk Conflict on TIMMS-SN00400 ==== November 10, 4:35 pm. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Sodder new charging port on iMet-XQ2 - Find Wire labels - Rain Gauges (Tipping Buckets) - Set up second Raspberry Pi - Wire Rain and fog gauges - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) - Update MAC addresses on Google Sheet "Computer-Access" for RAIN-SN00100, TippingBucket-SN00100, Electric Field Mill (E100), and CH601-Sonic - Resolve AnyDesk Conflict on TIMMS-SN00400 == Reports == * TIMMS - did not work on (DNW) * Check if must ID for current devices (keyboard, mouse) w/ Dr. Delene * Did not have correct charging ports for iMet-XQ2 - Check w/ Dr. Delene * Wire labels - talk to Dr. Delene * Rain Gauges - Fastened one AC plug * Tipping Bucket - DNW * Updated all listed MAC addresses * Did not resolve AnyDesk Conflict on TIMMS-SN00400 :( ==== November 6, evening. ==== == Tasks == - TIMMS-00400 - Raspberry Pi - Connect Temperature and Humidity Sensor - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS (Documentation) - Sodder new charging port on iMet-XQ2 - Find Wire labels - Rain Gauges - Set up second Raspberry Pi - Wire Rain and fog gauges == Reports == * Will USB identification build into TIMMS-00400 - Check if must do for current devices w/ Dr. Delene * TIMMS - did not work on (DNW) * Did not have correct charging ports for iMet-XQ2 - Check w/ Dr. Delene * Wire labels - talk to Dr. Delene * Built 3D printed catching apparatus, wired one AC plug ==== November 4, 6:14 pm. ==== == Tasks == - Create TIMMS-00400 - Set up Raspberry Pi - Connect Temperature and Humidity Sensor to Raspberry Pi - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Record hardware and software for TIMMS - Set up second Raspberry Pi - Sodder new charging port on iMet-XQ2 - Find Wire labels == Reports == * Will USB identification build into TIMMS-00400 - Check if must do for current devices w/ Dr. Delene * TIMMS-SN00400 - worked on reboot and usb connections * Set up Second Raspberry Pi * did not have correct charging ports for iMet-XQ2 - Check w/ Dr. Delene * Wire labels - talk to Dr. Delene ==== October 30, 4:50 pm. ==== == Tasks == - Create TIMMS-00400 - Set up Raspberry Pi - Connect Temperature and Humidity Sensor to Raspberry Pi - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Download and Access ADPAA Repository on personal laptop and Raspberry Pi and record methods - Add SVN software, record how to download software and ADPAA - Record hardware and software for TIMMS - Update Clifford Hall Combined Grafana page to look like Gorman Field Grafana page == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Must wait for Wi-Fi to TIMMS-00300 * Will build into TIMMS-00400 * Finished ADPAA and SVN Client page * TIMMS-SN00400 - No progress * Explored Grafana - task will be put on "back burner" for times when other work must be placed on pause. ==== October 27, 5:25 pm. ==== * Acquired power strip for camera box, 4 adapters == Tasks == - Create TIMMS-00400 - Set up Raspberry Pi - Connect Temperature and Humidity Sensor to Raspberry Pi - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Download and Access ADPAA Repository on personal laptop and Raspberry Pi and record methods - Add SVN software, record how to download software and ADPAA - Record hardware and software for TIMMS - Update Clifford Hall Combined Grafana page to look like Gorman Field Grafana page == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Must wait for Wi-Fi to TIMMS-00300 * Will build into TIMMS-00400 * Began working on ADPAA and SVN client, documentation started, client downloaded * TIMMS-SN00400 - need to access ADPAA first * Explored Grafana - task will be put on "back burner" for times when other work must be placed on pause. ==== October 24, 8:19 am. ==== * Met with Dr. Delane to discuss progress * Acquired 3D anemometer and USB Camera == Tasks == - Create TIMMS-00400 - Find Raspberry pi box (shell around computer for protection/looks) - Connect Temperature and Humidity Sensor to Raspberry Pi - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set up Raspberry Pi - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot - Download and Access ADPAA Repository on personal laptop and Raspberry Pi and record methods == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Must wait for Wifi to TIMMS-00300 * Will build into TIMMS-00400 * TIMMS-00400 * Emailed Wanda to order Raspberry Pi Box * Read manual for temperature and humidity sensor and discovered more documentation must be added. * Will look at ADPAA to see what past TIMMS set-ups have been * RECORD FINDINGS * No progress read fluxgate compass manual * Continued setting up Raspberry Pi * Got through [[https://atmoswiki.azurewebsites.net/doku.php?id=atmos:citation:instruments:raspberrypi_setup:home|Initial Raspberry Pi Setup Instructions]] * Next - Properly connect USB Camera (nearly done), connect temperature and humidity sensor * Began looking into downloading ADPAA * Must install SVN client * RECORD ALL FINDINGS ==== October 21, 8:45 am. ==== * Met with Dr. Delane to discuss progress * Acquired pressure sensor exterior and Fluxgate Compass * Raspberry Pi SD card was set up == Tasks == - Create TIMMS-00400 - Find Raspberry pi box (shell around computer for protection/looks) - Connect Temperature and Humidity Sensor to Raspberry Pi - Read manual for fluxgate compass and determine connection to Raspberry Pi - Set up Raspberry Pi - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Must wait for Wifi to TIMMS-00300 * Will build into TIMMS-00400 * TIMMS-00400 * No progress Raspberry Pi box * New task * No progress connect temp and humidity * New task * No progress read fluxgate compass manual * New task * Began setting up Raspberry Pi * Got through step 4 on [[https://atmoswiki.azurewebsites.net/doku.php?id=atmos:citation:instruments:raspberrypi_setup:home|Initial Raspberry Pi Setup Instructions]] * Maybe through 5? Will investigate further. * Set timezone and preferences * Updated Wiki pages throughout progress for future reference * Updated TIMMS-00400 for new parts ==== October 17, 8:40 am. ==== *Met with Dr. Delane to discuss progress *added more parts to list for TIMMS-00400 * Pressure Transducer * DAQ HAT * MicroSD Card * USB Camera * Ultrasonic 3D Anemometer * Radiation shield for temperature and humidity sensor * Will update TIMMS-00400 wiki entry == Tasks == - Create TIMMS-00400 - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == *Will remotely access TIMMS-00300 to properly identify devices * Must wait for Wifi to TIMMS-00300 * Will build into TIMMS-00400 * Connected Monitor to Raspberry Pi * Found proper power connection for Raspberry Pi * Updated TIMMS-00400 wiki entry ==== October 9, 7:00 pm. ==== * Remote Work == Tasks == - Create TIMMS-00400 - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Will build into TIMMS-00400 * Looked into Raspberry Pi configuration and set up * Read instrument manuals for ultrasonic anemometer and temperature and humidity sensor. ==== October 8, 8:00 am. ==== * Received box for TIMMS-00400 == Tasks == - Create TIMMS-00400 - Connect to Littlestorm - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Will build into TIMMS-00400 * Connected to Littlestorm * Analyzed new components for TIMMS-00400 ==== October 6, 5:15 pm. ==== * Met with Dr. Delane * Accessed ndus vpn instead of und vpn to connect to Littlestorm * Received numerous components to continue building TIMMS-00400 == Tasks == - Create TIMMS-00400 - Connect to Littlestorm - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == * Will remotely access TIMMS-00300 to properly identify devices * Will build into TIMMS-00400 * Waiting on email to finish connecting to Littlestorm * Began setting up Raspberry Pi for TIMMS-00400 * Set up mouse and keyboard * Looked at power supply and video output ports * need USBC for power supply * Found cord that worked * Does not have large wall adapter, as recommended by Dr. Delane. * Look into finding a cord with USBC connection and large adapter * Need micro-hdmi for video * On order ==== October 2, 7:30 pm. ==== * Remote Work == Tasks == - Create TIMMS-00400 - Parts List - Connect to Littlestorm - Connect to Grafana - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == *TO BE ADDRESSED AT NEXT MEETING (compilation) * Unable to connect to Littlestorm * Parts Uncertainty * Camera (which type) * Correct model of ultrasonic anemometer * Box (Camera or square) * UNUSED components (verify) * Pressure Transducer * DAQ HAT * Visibility Sensor * iMet-XQ2 UAV Sensor * Web Cam *DETAIL * Unable to connect to Littlestorm (connection timeout error) * Address at next meeting with Dr. Delane * Connected to Grafana * Parts List Progress * Collected wiki articles on instruments, TIMMS, and the MetTrailer * Began compiling more parts * Raspberry Pi 4B * Temp/Humidity Sensor * Tripod * Camera (USB or Pi cam) * Ultrasonic anemometer (Young Ultrasonic Anemometer Model 81000) * Camera Box or electrical box * NOT being used * Pressure Transducer * DAQ HAT * Visibility Sensor * iMet-XQ2 UAV Sensor * Web Cam * Set USB devices * Searched through wiki and online for guides * Found and recorded methods of assigning port identifiers for specific devices * Consult with Dr. Delane on updating TIMMS-00300, as it is deployed at the Glacial Ridge Field Site * Save records for application on TIMMS-00400 ==== Meeting September 30, 9 am. ==== * Have Wiki account and can edit things. * Order videos, comment monitor up the Raspberry Pi. == Tasks == - Create TIMMS-00400 - Parts List - Connect to Littlestorm - Set USB Devices on TIMMS-00300 and TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot == Reports == *Unable to connect to Littlestorm (connection timeout error) *Parts List Progress *Raspberry Pi 4B *Temp/Humidity Sensor *Tripod *Created Sourceforge account *Accessed Chords (data website) *Created Zotero account *Unable to access Grafana *Downloaded ADPAA *Collected atmos wiki sites for task 3, no other progress ==== Meeting September 26, 9 am. ==== === Discussion === * Asked John Wold to give Ashley a Wiki account. * Suggest working on a **temperate/sonic wind/ camera for the [[http://mettrailer.atmos.und.edu/|MetTrailer tower]]**. * Suggest making a TIMMS-00400 for the lower tower on the MetTrailer. * Meeting next week, 9 am check-in == Tasks == *Create TIMMS-00400 *Parts List *Connect to Littlestorm == Reports == *Unable to connect to Littlestorm (connection timeout error) *Parts List Progress *Raspberry Pi 4B *Temp/Humidity Sensor