Atmos Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Atmospheric Science 3D Printer Online Lab Book ======

**Latest information is given at the top.  Times and dates are local time.**

2018/12/06 11:30 - Nick Gapp: Printed 4x anemometer driveshaft, 4x wind vane driveshaft, 4x anemometer/wind vane body, 4x anemometer/wind vane bearing housing, and 3x wind vane alignment tool.

2018/12/05 18:38 - Nick Gapp: Printed wind vane parts--1x rotor, 1x body, 1x bearing housing, 1x driveshaft, 1x cover, 1x pointer, 1x pointer clamp bolt, 1x sensor holder disk, 1x base, 1x wind direction connector, 1x gripping tool.

2018/12/05 11:10 - Nick Gapp: Printed anemometer parts--3x cup, 1x hub, 1x body, 1x bearing housing, 1x driveshaft, 1x sensor holder, 1x base, and 1x 3-pin anemometer connector.

2018/11/29 19:40 - Shawn Wagner: Printed 4 tipping buckets.

2018/11/28 20:31 - Shawn Wagner: Created and printed the updated raingauge rim for calibrated setup (87.29 mm).

2018/11/02 15:45 - Nick Gapp: Printed for the rain gauge: 1x base, 1x cover with open sides ("cover inside inspection2"), and 3x counterbalance.

2018/11/01 16:55 - Nick Gapp: Tried printing 1x bucket, 1x cover with open sides ("cover inside fit inspection2"), and 2x counterbalance.  AfiniaStudio apparently crashed about halfway through the print, so the only thing to finish printing was the bucket.

2018/10/31 15:10 - Nick Gapp: Printed for rain gauge: 1x fixed funnel.

2018/10/30 20:00 - Nick Gapp: Printed wiring: 8x small lock nut and 8x tapered cable cover.

2018/10/27 22:00 - Shawn Wagner: Printing 4x 3 hole setting tool; 4x 4 hole setting tool; 1x 3 pos shunt; 4x 4 pos shunt; 3x 5 pos shunt .   

2018/10/27 unknown - David Delene (updated by Shawn Wagner): Printing 4x 3 hole setting tool; 3x 4 hole setting tool; 1x 3 pos shunt; 3x 5 pos shunt; 2x 6 pos shunt.   

2018/10/27 02:28 - David Delene: Printing 8x each: 3 pin male locking Rain, 3 pin male locking VelociT, 4 pin male locking thread small (cable_designs). 

2018/10/26 15:18 - Shawn Wagner: Printing 8x each: 3 pin male locking Rain, 3 pin male locking VelociT, 4 pin male locking thread small (cable_designs). 

2018/10/26 14:15 - David Delene: Printing 10x: cover for mcp3002. Printing 4x each: R Pi GPIO collar, R Pi GPIO with 2 x 5v (GPIO designs).

2018/10/26 03:12 - Shawn Wagner: Printing 10x: cover for mcp3002. Printing 4x each: R Pi GPIO collar, R Pi GPIO with 2 x 5v (GPIO designs).

2018/10/24 20:37 - Mariusz Starzec: Printing 4x each: 6 pos shunt, 5 pos shunt. Printing 12x 3 pos shunt for wiring (GPIO designs).

2018/10/24 15:30 - Mariusz Starzec: Printing 3x each: 6 pos shunt, 5 pos shunt, 3 pos shunt. 

2018/10/23 14:35 - Mariusz Starzec: Printing 3x each: standard connector T, H, BMP280, and 4 pos shunt (rad-shield harness designs). Printing 1x each: 6 pos shunt, 5 pos shunt, 3 pos shunt, R Pi GPIO collar and cover (GPIO designs).

2018/10/19 16:21 - Mariusz Starzec: Printing 7x tapered cable covers, 6x small lock nut, 3x 4-pin male locking thread (small), 3x 3-pin male locking thread (wind direction), 3x 3-pin male locking thread (velocity), 3x 3-pin male locking thread (rain)

2018/10/10 09:09 - Nicole Loeb: Printed 4x locking thread (small), 4x fastener, 1x locking thread, 1x swivel pipe, and 1x swivel lock nut. --Cancelled because ran out of filament.

2018/10/09 15:00 - Nicole Loeb: Printed 6 wire holders and 6 wire plugs.

2018/10/09 13:00 - Nicole Loeb: Printed 12 soldering jigs. 

2018/10/05 11:06 - Matt Tuftedal: Printed 28 fasteners, a tipping bucket and 10 r, 10 t, and 10 4 pin connectors. more solder jigs need to be printed but we are very low on plastic. 

2018/09/26 18:00 - Nick Gapp: Printed for Pi tube assembly ("frame"): 1x securing band, 1x securing band threaded.

2018/09/26 11:00 - Nick Gapp: Printed for rain gauge ("wiring"): 1x small lock nut, 1x 3-pin male locking connector, 1x tapered cable cover. Printed for rain gauge calibration mounting arm: 1x swivel adapter, 1x securing nut. Printed for Pi tube assembly ("frame"): 6x securing bolts.

2018/09/25 14:30 - Nick Gapp: For rain guage: Printed 1x counterbalance, 2x stops (which is 12 pieces total), 1x bottle hanger for calibration, 1x rivet trimming guide (bottle hanger and guide not in parts list but used for calibration).

2018/09/21 22:00 - Mariusz Starzec: Printed 1x screen ring for radiation shield. Printed all parts for GPIO Harness. Print log: 1x Cover, 1x GPIO connector, 1x GPIO connector collar, 2x 3-pin rail connector, 1x 5-pin rail connector, 1x 6-pin rail connector, 1x 3-pin locking (rain) connector, 1x 3-pin locking (velocity) connector, 1x 3-pin locking (direction) connector, 2x 4-pin locking subconnector. Left to do for tipping bucket: Reprint bucket and print 2x stop, 1x locking thread, 1x funnel, 1x cover, 1x soldering jig, and 1x rivet trimming guide. For radiation shield: Using 5 open leafs and 2 screen rings from previous weather station print (will need to print 5 open leafs and 4 screen rings in the future once this station is all done).

2018/09/20 21:01 - Mariusz Starzec: Printed 1x soldering jig for circuit board soldering ("Soldering Circuit boards" section completed). Printed radiation shield harnesses: 1x 4 pin setting tool, 5x 4 pin common rail connectors, 1x temperature sensor housing, 1x pressure sensor housing, 4x humidity sensor housing, 1x 4 pin female connector (Radiation shield harnesses sections completed).

2018/09/20 11:15 - Shawn Wagner: Printed 1x locking thread, 1x bucket, 1x base for tipping bucket. Still need: 2x stop and 1x locking thread for bucket. Need to reprint bucket.

2018/09/19 06:02 - Shawn Wagner: Printed for radiation shield: 1x screen ring; for tipping bucket: 2x fasteners. Still need for radiation shield 3x screen ring; for tipping 1x bucket, 1x counterbalance, 2x stop, 1x base, 1x locking threads.  

2018/09/19 20:41 - Shawn Wagner: Printed for light sensor: 1x 4 pin connector, 1x cover, 1x base. Completed light sensor printing. Still need 5x open leaf, and 4x screen ring for radiation shield.

2018/09/18 19:38 - Shawn Wagner: Printed for radiation shield: 1x base, 1x base plate. Still required" 5x open leaf, 4x screen ring.

2018/09/17 17:00 - Shawn Wagner: Printed "For Making Cables": 4x locknut, 8x tapered cable cover, 4x 3 pin male adapter, 4x 4 pin male adapter. "For Making Cables" section 3D printing complete. 

2018/09/12 20:46 - Nicole Loeb: Printed small base plate & next to top leaf. The following still needs to be printed for the radiation shield: 5x open leaf, 4x screen ring, 1x base, 1x base plate.


2018/09/12 10:58 - Mariusz Starzec: Successfully printed soldering jig (and printed an extra just in case it breaks when putting the anemometer together). Did not use a raft for this piece and recommend not using rafting for the future for similar small and fragile pieces; however, have to make sure hardened acetone solution base is smooth and does not have many imperfections before printing.

2018/09/11 20:44 - Nicole Loeb: Jig broke again. Started print of Radiation Shield top leaf, center screen, and shaft.

2018/09/11 18:44 - Nicole Loeb: Reprinted jig with lower infill (on its own).

2018/09/11 13:53 - Nicole Loeb: Printed wind wrench, and started Radiation Shield printing (2x fastener, locking threads, jig, lock nut & swivel pipe end). Ran out of material during printing of locking thread and replaced the spool but the print looks ok. Jig broke while separating from base.

2018/09/07 15:57 - Matt Tuftedal: The soldering jig needs to be reprinted, it broke when coming off the plastic. Today I printed everything for the wind vane except for the "wind vane clamp" also called gripping tool on the parts list online. 

2018/09/05 13:15 - Matt Tuftedal: Printed the 3 Cups for the anemometer, hub, body, bearing housing, driveshaft, sensor holder, 3 pin anemometer connector, and soldering jig. For the wind vane so far the cover, wind direction connector, alignment clip and alignment cap, and bearing holder. 

2018/08/31 14:21 - Mariusz Starzec: Finished printing rain gauge cover (rain gauge #16)

2018/08/30 12:28 - David Delene:  Create the notebook.