atmos:researchmeetingnotes:researchmeetingnotes:home:ashley_vos
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| atmos:researchmeetingnotes:researchmeetingnotes:home:ashley_vos [2025/11/20 22:48] – ashley.vos | atmos:researchmeetingnotes:researchmeetingnotes:home:ashley_vos [2025/12/02 02:47] (current) – ashley.vos | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Ashley Vos Undergraduate Research (Aerospace Engineering) ===== | ===== Ashley Vos Undergraduate Research (Aerospace Engineering) ===== | ||
| Interest in the surface measurement instrument. Interested in probe flow modeling and ground electric field mills. | Interest in the surface measurement instrument. Interested in probe flow modeling and ground electric field mills. | ||
| + | |||
| + | ==== December 1st, 5:42 pm. ==== | ||
| + | |||
| + | == Tasks == | ||
| + | - TIMMS-00400 | ||
| + | - Raspberry Pi | ||
| + | - Connect Temperature and Humidity Sensor | ||
| + | - Read manual for fluxgate compass and determine connection to Raspberry Pi | ||
| + | - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot | ||
| + | - Record hardware and software for TIMMS (Documentation) | ||
| + | - Pressure Transducer - find one to buy (cheap, highest accuracy) | ||
| + | - Young, Campbell | ||
| + | - Must connect to A/D board | ||
| + | - Research SPI and IC2 interface | ||
| + | - Sodder new charging port on iMet-XQ2 | ||
| + | - Find type (read manual) and order | ||
| + | - Look into how to label small wires | ||
| + | - Rain Gauges (Tipping Buckets) | ||
| + | - Wire Rain and fog gauges | ||
| + | - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) | ||
| + | - Wire Aerosol to Power Control Device - will need to find manual. | ||
| + | - Connect to Wi-Fi | ||
| + | - Record how to set up DAQ HATS | ||
| + | - Create append method for ADPAA (Note: / | ||
| + | == Reports == | ||
| + | * TIMMS - DNW | ||
| + | * iMet-XQ2 - Soldered new charging ports onto both devices at the bench. Need to test - Inquire with Dr. Delene | ||
| + | * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work. Confirmed with Dr. Delene, will work without it and see if it becomes necessary. | ||
| + | * Rain Gauges - Wired another AC Plug | ||
| + | * Tipping Bucket Programming - DNW | ||
| + | * Aerosol Particle Sizer - DNW | ||
| + | * Wi-Fi - Connected. | ||
| + | * DAQ HATS - Done. | ||
| + | * Append - DNW. New Task | ||
| + | |||
| + | ==== November 24, 4:38 pm. ==== | ||
| + | |||
| + | == Tasks == | ||
| + | - TIMMS-00400 | ||
| + | - Raspberry Pi | ||
| + | - Connect Temperature and Humidity Sensor | ||
| + | - Read manual for fluxgate compass and determine connection to Raspberry Pi | ||
| + | - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot | ||
| + | - Record hardware and software for TIMMS (Documentation) | ||
| + | - Pressure Transducer - find one to buy (cheap, highest accuracy) | ||
| + | - Young, Campbell | ||
| + | - Must connect to A/D board | ||
| + | - Research SPI and IC2 interface | ||
| + | - Sodder new charging port on iMet-XQ2 | ||
| + | - Find type (read manual) and order | ||
| + | - Look into how to label small wires | ||
| + | - Rain Gauges (Tipping Buckets) | ||
| + | - Wire Rain and fog gauges | ||
| + | - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one) | ||
| + | - Wire Aerosol to Power Control Device - will need to find manual. | ||
| + | - Connect to Wi-Fi | ||
| + | - Record how to set up DAQ HATS | ||
| + | == Reports == | ||
| + | * TIMMS - Finished setting up Vaisala Temperature and Humidity sensor; recorded first data! | ||
| + | * Recorded how to set up ADPA and how to set up the Vaisala Temperature and Humidity Probe | ||
| + | * iMet-XQ2 - The ones we have work, but we'd have to flip the orientation. Could do it. | ||
| + | * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work. | ||
| + | * Rain Gauges - DNW | ||
| + | * Tipping Bucket Programming - DNW | ||
| + | * Aerosol Particle Sizer - Coded in data acquisition parameters save for the last one. | ||
| + | * Wi-Fi - Will work, just need username from Dr. Delene | ||
| ==== November 20, 4:46 pm. ==== | ==== November 20, 4:46 pm. ==== | ||
| Line 23: | Line 89: | ||
| - Wire Aerosol to Power Control Device | - Wire Aerosol to Power Control Device | ||
| == Reports == | == Reports == | ||
| - | * TIMMS - | + | * TIMMS - DNW |
| - | * iMet-XQ2 - | + | * iMet-XQ2 - The ones we have work, but we'd have to flip the orientation. Could do it. |
| - | * Wires- | + | * Wires- |
| - | * Rain Gauges - | + | * Rain Gauges - DNW |
| * Tipping Bucket Programming - | * Tipping Bucket Programming - | ||
| - | * Aerosol Particle Sizer - | + | * Aerosol Particle Sizer - Began wiring |
| ==== November 19, 5:32 pm. ==== | ==== November 19, 5:32 pm. ==== | ||
atmos/researchmeetingnotes/researchmeetingnotes/home/ashley_vos.1763678880.txt.gz · Last modified: 2025/11/20 22:48 by ashley.vos