Differences

This shows you the differences between two versions of the page.

--- atmos:researchmeetingnotes:researchmeetingnotes:home:ashley_vos [2025/11/20 02:44] – ashley.vos
+++ atmos:researchmeetingnotes:researchmeetingnotes:home:ashley_vos [2025/12/02 02:47] (current) – ashley.vos
@@ Line 1: / Line 1: @@
 ===== Ashley Vos Undergraduate Research (Aerospace Engineering) =====
   Interest in the surface measurement instrument. Interested in probe flow modeling and ground electric field mills.
+==== December 1st, 5:42 pm. ====
+== Tasks ==
+  - TIMMS-00400
+    - Raspberry Pi
+      - Connect Temperature and Humidity Sensor
+      - Read manual for fluxgate compass and determine connection to Raspberry Pi
+      - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot
+    - Record hardware and software for TIMMS (Documentation)
+    - Pressure Transducer - find one to buy (cheap, highest accuracy)
+      - Young, Campbell
+      - Must connect to A/D board
+      - Research SPI and IC2 interface
+  - Sodder new charging port on iMet-XQ2
+    - Find type (read manual) and order
+  - Look into how to label small wires
+  - Rain Gauges (Tipping Buckets)
+    - Wire Rain and fog gauges
+  - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one)
+  - Wire Aerosol to Power Control Device - will need to find manual.
+  - Connect to Wi-Fi
+  - Record how to set up DAQ HATS
+  - Create append method for ADPAA (Note: /home/raspberry/ADPAA/src/python_lib)
+== Reports ==
+  * TIMMS - DNW
+  * iMet-XQ2 - Soldered new charging ports onto both devices at the bench. Need to test - Inquire with Dr. Delene
+  * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work. Confirmed with Dr. Delene, will work without it and see if it becomes necessary.
+  * Rain Gauges - Wired another AC Plug
+  * Tipping Bucket Programming - DNW
+  * Aerosol Particle Sizer - DNW
+  * Wi-Fi - Connected.
+  * DAQ HATS - Done.
+  * Append - DNW. New Task
+==== November 24, 4:38 pm. ====
+== Tasks ==
+  - TIMMS-00400
+    - Raspberry Pi
+      - Connect Temperature and Humidity Sensor
+      - Read manual for fluxgate compass and determine connection to Raspberry Pi
+      - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot
+    - Record hardware and software for TIMMS (Documentation)
+    - Pressure Transducer - find one to buy (cheap, highest accuracy)
+      - Young, Campbell
+      - Must connect to A/D board
+      - Research SPI and IC2 interface
+  - Sodder new charging port on iMet-XQ2
+    - Find type (read manual) and order
+  - Look into how to label small wires
+  - Rain Gauges (Tipping Buckets)
+    - Wire Rain and fog gauges
+  - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one)
+  - Wire Aerosol to Power Control Device - will need to find manual.
+  - Connect to Wi-Fi
+  - Record how to set up DAQ HATS
+== Reports ==
+  * TIMMS - Finished setting up Vaisala Temperature and Humidity sensor; recorded first data!
+      * Recorded how to set up ADPA and how to set up the Vaisala Temperature and Humidity Probe
+  * iMet-XQ2 - The ones we have work, but we'd have to flip the orientation. Could do it.
+  * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work.
+  * Rain Gauges - DNW
+  * Tipping Bucket Programming - DNW
+  * Aerosol Particle Sizer - Coded in data acquisition parameters save for the last one.
+  * Wi-Fi - Will work, just need username from Dr. Delene
+==== November 20, 4:46 pm. ====
+== Tasks ==
+  - TIMMS-00400
+    - Raspberry Pi
+      - Connect Temperature and Humidity Sensor
+      - Read manual for fluxgate compass and determine connection to Raspberry Pi
+      - Set USB Devices on TIMMS-00400 Raspberry Pi to properly identify devices in port 1 and 2 on reboot
+    - Record hardware and software for TIMMS (Documentation)
+    - Pressure Transducer - find one to buy (cheap, highest accuracy)
+      - Young, Campbell
+      - Must connect to A/D board
+      - Research SPI and IC2 interface
+  - Sodder new charging port on iMet-XQ2
+    - Find type (read manual) and order
+  - Look into how to label small wires
+  - Rain Gauges (Tipping Buckets)
+    - Wire Rain and fog gauges
+  - Program TippingBucket-SN00100 or Rain-SN00100 (Confirm with Dr. Delene which one)
+  - Wire Aerosol to Power Control Device
+== Reports ==
+  * TIMMS - DNW
+  * iMet-XQ2 - The ones we have work, but we'd have to flip the orientation. Could do it.
+  * Wires- could buy wire shrink printer, cheapest around 30-50 dollars, regular around 100-300. Otherwise buy smaller tape for the label maker, and just make it work.
+  * Rain Gauges - DNW
+  * Tipping Bucket Programming -
+  * Aerosol Particle Sizer - Began wiring
 ==== November 19, 5:32 pm. ====