atmos:3dprinter:prusa
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| atmos:3dprinter:prusa [2026/07/29 16:03] – halmos | atmos:3dprinter:prusa [2026/07/29 18:25] (current) – halmos | ||
|---|---|---|---|
| Line 8: | Line 8: | ||
| Important Information | Important Information | ||
| - | * When setting up PrusaSlicer, | + | * When setting up PrusaSlicer, |
| * There is a multitude of different materials available for printing that require different profiles. BEFORE printing it is incredibly important you verify the type of filament inserted. Damage can occur if the hotend is not heated to the appropriate temperature for the type of filament. | * There is a multitude of different materials available for printing that require different profiles. BEFORE printing it is incredibly important you verify the type of filament inserted. Damage can occur if the hotend is not heated to the appropriate temperature for the type of filament. | ||
| + | * To connect to printer, you must create a Prusa account and be invited to the team. Email jacob.halmos@und.edu with the email address you used to create the account so you can be added. | ||
| ====== Printing Process ====== | ====== Printing Process ====== | ||
| ===== Inserting Filament ===== | ===== Inserting Filament ===== | ||
| Line 35: | Line 36: | ||
| * After the part has been removed, ensure the build plate is securely put back in place, and clean of fingerprints / debris. Set printer state to " | * After the part has been removed, ensure the build plate is securely put back in place, and clean of fingerprints / debris. Set printer state to " | ||
| ====== Switching Filament ====== | ====== Switching Filament ====== | ||
| + | * On the main menu, click FILAMENT | ||
| + | * Click " | ||
| + | * The filament will not obviously move, however, once the process is complete, carefully but not forcefully pull the filament out of the tube on the right hand side where the spool of filament is. | ||
| + | * Remove the spool | ||
| + | * Replace with new spool, ensuring direction is correct to provide the path of least resistance. | ||
| + | * Insert filament. You will need to press relatively firm at first to pass through the sensor, however it will need to make it all the way to the hot end and will not be able to be pushed in further before clicking the LOAD button. | ||
| + | * Click " | ||
| ====== Common Errors ====== | ====== Common Errors ====== | ||
| ===== Printer is not connected to Prusa Connect ===== | ===== Printer is not connected to Prusa Connect ===== | ||
| Line 40: | Line 48: | ||
| ====== Materials Guide ====== | ====== Materials Guide ====== | ||
| + | * https:// | ||
| + | * If using PETG, it is highly recommended to use the textured sheet (not available in ATSC lab.) Since we do not have access to it, another method is to put a thin layer of glue stick down on the surface where you will be printing. Failure to do this can result in the part being impossible to remove from the bed, damage to the bed, and more. | ||
| ====== Printer Manuals ====== | ====== Printer Manuals ====== | ||
| * https:// | * https:// | ||
| - | + | ====== Point of Contact ====== | |
| + | * David Delene | david.delene@UND.edu | ||
| + | * Jacob Halmos | jacob.halmos@UND.edu | ||
atmos/3dprinter/prusa.1785341004.txt.gz · Last modified: 2026/07/29 16:03 by halmos