atmos:3dprinter:prusa
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| atmos:3dprinter:prusa [2026/07/28 19:32] – halmos | atmos:3dprinter:prusa [2026/07/29 18:25] (current) – halmos | ||
|---|---|---|---|
| Line 8: | Line 8: | ||
| Important Information | Important Information | ||
| - | * When setting up PrusaSlicer, | + | * When setting up PrusaSlicer, |
| * There is a multitude of different materials available for printing that require different profiles. BEFORE printing it is incredibly important you verify the type of filament inserted. Damage can occur if the hotend is not heated to the appropriate temperature for the type of filament. | * There is a multitude of different materials available for printing that require different profiles. BEFORE printing it is incredibly important you verify the type of filament inserted. Damage can occur if the hotend is not heated to the appropriate temperature for the type of filament. | ||
| + | * To connect to printer, you must create a Prusa account and be invited to the team. Email jacob.halmos@und.edu with the email address you used to create the account so you can be added. | ||
| ====== Printing Process ====== | ====== Printing Process ====== | ||
| ===== Inserting Filament ===== | ===== Inserting Filament ===== | ||
| Line 23: | Line 24: | ||
| - Connect USB stick to computer and drag / drop GCode file to USB Stick | - Connect USB stick to computer and drag / drop GCode file to USB Stick | ||
| - Insert USB stick to printer | - Insert USB stick to printer | ||
| + | - A prompt should appear with the newly added file. | ||
| - Click " | - Click " | ||
| - Once print has completed, remove USB stick and delete GCode file. | - Once print has completed, remove USB stick and delete GCode file. | ||
| ===== Sending the File to the Printer - Prusa Connect ===== | ===== Sending the File to the Printer - Prusa Connect ===== | ||
| - | - In Prusa Slicer, click "Send to prusa connect | + | - In Prusa Slicer, click "Send to prusa connect" once slicing is complete. |
| ===== Removing the Part ===== | ===== Removing the Part ===== | ||
| + | * After printing has completed, it is important that you completely wait for the bed to return to room temperature before attempting to remove the part. | ||
| + | * To remove, carefully lift the plate off the surface and slightly bend it. The part should naturally release. NOTE: In some instances using different materials / supports, it may be difficult to remove parts. DO NOT try to use your fingernail. Instead, use a plastic scraper (near the printer) to get underneath the part and carefully lift it. | ||
| + | * Avoid excessive fingerprints on the build plate. This can lead to failed prints due to parts lifting off the surface before printing has completed. If this occurs, carefully wipe build plate with isopropyl alcohol. | ||
| + | ===== Preparing printer for next user ===== | ||
| + | * After the part has been removed, ensure the build plate is securely put back in place, and clean of fingerprints / debris. Set printer state to " | ||
| ====== Switching Filament ====== | ====== Switching Filament ====== | ||
| - | ====== | + | * On the main menu, click FILAMENT |
| + | * Click " | ||
| + | * The filament will not obviously move, however, once the process is complete, carefully but not forcefully pull the filament out of the tube on the right hand side where the spool of filament is. | ||
| + | * Remove the spool | ||
| + | * Replace with new spool, ensuring direction is correct to provide the path of least resistance. | ||
| + | * Insert filament. You will need to press relatively firm at first to pass through the sensor, however it will need to make it all the way to the hot end and will not be able to be pushed in further before clicking the LOAD button. | ||
| + | * Click " | ||
| + | ====== | ||
| + | ===== Printer is not connected to Prusa Connect ===== | ||
| + | * In certain instances, the printer will show as OFFLINE on prusa connect. This is due to the limited range of the WIFI module in the printer. A short term solution I have found is to press the RESET button on the display of the printer. If this still does not work, manual printing using the included USB drive is required. | ||
| + | ====== Materials Guide ====== | ||
| + | * https:// | ||
| + | * If using PETG, it is highly recommended to use the textured sheet (not available in ATSC lab.) Since we do not have access to it, another method is to put a thin layer of glue stick down on the surface where you will be printing. Failure to do this can result in the part being impossible to remove from the bed, damage to the bed, and more. | ||
| + | ====== Printer Manuals ====== | ||
| + | * https:// | ||
| + | ====== Point of Contact ====== | ||
| + | * David Delene | david.delene@UND.edu | ||
| + | * Jacob Halmos | jacob.halmos@UND.edu | ||
atmos/3dprinter/prusa.1785267164.txt.gz · Last modified: 2026/07/28 19:32 by halmos